Masse d'égalisation PCI Pericret® 25 kg
PCI Pericret 25kg
est un mortier d'égalisation cimentaire à prise rapide pour supports minéraux sur murs, sols et plafonds, à utiliser avant le matériau de finition. Il est destiné à être appliqué sur des surfaces intérieures et extérieures, par exemple sur des terrasses, des balcons et des piscines. Très facile à appliquer, plastique et façonnable après ajout d'un peu d'eau.
PCI Pericret est très facile à appliquer. Plastique et façonnable après ajout d'un peu d'eau. Grâce à son imperméabilité et à sa résistance aux intempéries et au gel, il peut être utilisé à l'intérieur et à l'extérieur. La large gamme d'épaisseurs de couche (surfaces 3 - 30 mm, joints 3 - 50 mm) en fait un mortier d'égalisation très polyvalent.
PCI Pericret sac de 25kg, lorsque la couche est censée avoir une épaisseur de 3mm, couvrira jusqu'à 6,4m². La surface peut être carrelée après environ 2 heures.
Features and benefits:
- Fast setting, can be tiled or re-plastered after approx. 2 hours.
- Waterproof, resistant to weathering and frost, multi-purpose use indoors and out.
- Plastic and workable when water is added, easy to apply.
- Low shrinkage during the curing phase.
- Very low emission.
Fields of application:
- For indoor and outdoor use.
- For floors, walls and soffits.
- On concrete and masonry.
- On gauged render and render.
- On plasterboards and plaster.
- For use on existing ceramic tiles.
- Base coat and/or levelling coat on masonry before applying rubbedfinished render, scratch render or polymer render.
- To level and repair irregular wall surfaces before tiling.
- To level concrete floors and cement screeds, to produce smooth sloped levelling layers prior to laying floor tiles.
- To fix PCI Pecidur HR foam shower floor elements.
- Layer thickness: surfaces 3 - 30 mm, break-outs 3 - 50 mm.
- Base du matériau
- ciment spécial avec additifs
- Composants
- Composant unique
- Taille de l'emballage
- 25 kg Sac en papier doublé PE pour charges lourdes stock no. 3680/8
- Durée de conservation
- min. 6 mois en cas de stockage au sec, pas de stockage permanent à plus de +30°C
- Consommation
- Env. 1.3 kg/m² et mm épaisseur de la couche
- Température de travail
- +5 °C to +25°C (température du substrat)
- Temps de travail
- env. 30 - 40 minutes
- Cohérence
- poudre
- Couleur
- Gris
- Épaisseur minimale de la couche
- 3 mm
- Épaisseur maximale de la couche
- 50 mm
- Couverture d'une épaisseur de 3 mm
- 6,4 m² / sac de 25 kg couvre env.
- 10 mm d'épaisseur de couche couverture
- 1,9 m² / sac de 25 kg couvre approx.
- 20 mm épaisseur de la couche couverture
- 1,0 m² / sac de 25 kg couvre env.
- Mesure de l'eau pour un sac de 25 kg
- environ 4,8 - 5,0 l d'eau
- Temps de séchage
- peut être carrelé après env. 2 heures
Preparation of substrate
The substrate must be clean, structurally sound, open-porous, absorbent, free of dust, damp and able to take loads. Prime very absorbent substrates (e.g. sand-lime brick) with PCI Gisogrund, diluted 1 : 1 with water (undiluted for gypsum based substrates), alternatively with undiluted PCI Gisogrund Rapid. Substrates which are very absorbent and insensitive to water can also be intensively pre-wet. Prime non-absorbent substrates (e.g. ceramic tiles) with PCI Gisogrund 303.
Application procedure
- Pour water in a clean mixing container and add the required quantity of PCI Pericret while mixing with a suitable paddle (e.g. from Collomix) attached to a high-speed electric drill until a lumpfree, plastic consistency is produced.
- Using a finishing trowel, apply a thin scratch coat with PCI Pericret to the clean substrate before applying the mortar to the entire surface.
- PCI Pericret can be applied in one layer to a thickness of 50 mm (for break-outs) and 30 mm (for surfaces).
- When the mortar has initially set (approx. 30 to 90 minutes depending on layer thickness, substrate and working temperature) PCI Pericret can be rubbed down with a damp felt board or sponge float (Moltopren sponge, porous) or smoothed with a finishing trowel or short double plane if necessary.
- The substrate must be prewet and protected against rapid drying in high temperatures, wind and direct sunlight (e.g. repeated sprinkling with water, covering with jute or PE foil).
Please note:
- Never add water or wet PCI Pericret to reconstitute a mortar mix which has already begun to set.
- PCI Pericret is unsuitable when acting as a substrate for reaction resin coatings.
- Suitable tools are available from e.g. Collomix GmbH Horchstraße 2 85080 Gaimersheim/Germany www.collomix.de.
- Clean tools and mixing containers with water immediately after use; when the product has cured it can only be removed by mechanical scraping.
- Shelf life: min. 6 months when stored in dry conditions, no permanent storage over +30°C.